![]() So going back to the original issue, was my machine bringing up the UEFI loader first and then when I hit Exit it would load up the legacy one? This has been very confusing but I'm so glad it is working now. If I set it to anything with UEFI in it I would get the low res bootloader that would give me the Windows boot errors. ![]() In order to finally get it to work I set it to "Boot legacy only" and set my boot device to P0 (the Clover drive). That being said, I think I may have my issue mixed up, I think my issue may be that it was booting UEFI and I needed the legacy entry. I can even use the Startup Disk pane now to tell it which OS to reboot. After that I had more flexibility in selecting the boot entries and was able to default it to go into the entry that was giving me a proper Windows boot. What I WAS able to do though was upgrade my board to UEFI, they were released on the cusp of UEFI and shipped with a legacy BIOS despite supporting UEFI. I tried reinstalling the EFI with Multibeast but I wasn't able to get it to work. Is there some way for me to force Clover to boot into whatever that second menu is so it'll properly boot Windows? Proposed solution: I noticed today that if I exit what appears to be the Clover legacy bootloader, I am then taken into the Clover UEFI bootloader (it's higher res, more devices show up, mouse semi-works), and selecting Windows will in fact boot it. In general, install Windows using the newer UEFI mode, as it includes more security features than the legacy BIOS mode. After Windows is installed, if you need to switch firmware modes, you may be able to use the MBR2GPT tool. My workaround has been to just boot straight into the Win 7 drive from the BIOS boot drive select which has worked fine. Choose UEFI or legacy BIOS modes when booting into Windows PE (WinPE) or Windows Setup. Issue: My primary issue is that when I try to boot Win 7 from the Clover menu I am greeted with a boot error. FYI I think I have a weird hybrid legacy/UEFI board but I've mostly used it as legacy over these years. I believe one of the issues I created may have been from installing both the legacy and UEFI version of Clover and fudging up the boot entries. There was a absurd amount of troubleshooting (primarily isolating the Win 7 install) and along the way I created, resolved, and created more boot issues with the Win 7 boot entry. Shortly after that I split them onto two separate drivers. Also now I can even utilize the Startup Disk pane which is very convenient for rebooting into Windows remotely.īackground: Many months ago I did a fresh El Capitan install on a drive it shared with Win 7. That being said, I think my issue may have been mixed up, I think I had Clover in UEFI instead of legacy which I needed to boot Windows, if that makes sense. I was able to get more boot entry flexibility and was able to choose the correct version of Clover that'd boot my Windows properly. Solution:I installed the UEFI BIOS upgrade for my originally legacy motherboard. Will these be enough as this is a clean installation and the respective hardware information, for power, ROM and misc, should be collected and updated whilst installing or will it? I would rather do this once correctly so am checking this out before.Building a CustoMac Hackintosh: Buyer's Guide For these I intend to add them from clover bootloader, but all of these directories have empty files within. I have all of the directories and files except for these three directories ACPI, ROM and Misc. I have mostly set up the EFI folder contents for clover bootloader. Then I should be able to start the clean installation process of windows 10 which is 64-bit hence the need for another bootloader. I will then copy clover bootloader over to the EFI folder on the EFI system partition then set the path for BCD. So after I have set up the partitions (shift + F10 before installing windows) from command prompt - please note the automatic set up of partitions is not working. I am going to install clover bootloader whilst clean installing windows 10 for BIOS UEFI (but the BIOS UEFI are 32-Bit).
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |